Use the speed command to change the speed on the interface and use the show interface command to see what speed is currently configured for each interface. When the active license expires, you need to manually activate the new one. For that you can follow the Quick Start Guide. It is just showing me some time based activity. When you are prompted to save the configuration before reloading, answer No. They are treated as separate licenses and do not benefit from the combined license. Note Some features are incompatible with each other.
Detailed Steps Command Purpose show activation-key detail Example: hostname show activation-key detail Shows the installed licenses, including information about temporary licenses. Reg, Sushil Yes,I ordered ssl licenses only. You can upgrade from 7. For example, if the permanent license is 1000 sessions, and the time-based license is 2500 sessions, then 2500 sessions are enabled. Some applications might use multiple sessions for a connection. This feature is not available in Version 8. The interface associated with the default route is considered to be the outside Internet interface.
You can only deactivate Time-Based Keys as per the. The flash activation key was updated with the requested key, and will become active after the next reload. Therefore, you can configure up to 5 contexts on the primary unit; each secondary unit will also have 5 contexts through configuration replication. When the primary unit from Pair 1 goes down, the standby unit immediately becomes the new main licensing server. The last license you activate is the one in use. Do I need to buy the same licenses for the secondary unit in a failover pair? In the Base license, they continue to be used as Fast Ethernet 100 Mbps ports. Related Tasks No Payload Encryption Models You can purchase some models with No Payload Encryption.
See the quick start guide for your model for more information. You may be able to purchase a larger license at an upgrade price, for example from 25 sessions to 75 sessions; this kind of upgrade should be distinguished from adding two separate licenses together. Make sure this license is for the standby unit serial number. It does not need a participant license as well as the server license to participate. The participant leaves existing connections established, but cannot accept new connections beyond the license limit.
Upgrading Failover Pairs Because failover pairs do not require the same license on both units, you can apply new licenses to each unit without any downtime. Detailed Steps Command Purpose On the active unit: Step 1 no failover Example: active config no failover Disables failover on the active unit. You have to enter each key as a separate process. You can repeat this command for as many interfaces as desired. The shared licensing server responds with information about how often the participant should poll the server.
Typically, this is how you receive all time-based activation keys from Cisco. Example 3-2 Successfully Activated Permanent Key ciscoasa activation-key 813cd670 704cde05 810195c8 e7f0d8d0 4e23f1af Validating activation key. For example, you have a network with 2 failover pairs. AnyConnect for Mobile License 8. For a shared licensing server, you need to buy the same shared licensing server license for both units. Step 5 If you have additional Product Authorization Keys, repeat for each Product Authorization Key.
It sends the scan results to the adaptive security appliance. Feature licenses cannot be transferred between devices except in the case of a hardware failure. The running key defaults to the permanent key value of 10 sessions. All other models Base License or Standard License. For example, a small business with 15 employees may start out with a with a 25-user or, more correctly, 25-host license.
For licenses that have a status of enabled or disabled, then the license with the enabled status is used. Other time-based keys remain installed but inactive until needed. This license is applied by simply using the activation-key command. If Pair 1 remains down, and the primary unit in Pair 2 goes down, then the standby unit in Pair 2 comes into use as the shared licensing server see the following figure. Keep in mind that both the current and new time-based keys must enable only one feature with the exact same capacity, if applicable; otherwise, the new key will deactivate and replace the current one. Time-based features show the remaining number of days before expiration; even if you enable one of these features via the permanent key later on, the countdown will continue until the applicable time-based key expires or becomes deactivated manually.
See the following table for precise licensing requirements for failover. If the licenses are not identical for example, a 1000-session AnyConnect Premium license vs. When the main server comes back up, it syncs with the backup server, and then takes over server operation. You can only specify one backup server. To avoid unexpected network outages, it is very important to monitor time-based licenses for expiration and replace them in advance; always use permanent licenses for the critical features when possible. Example 3-6 shows the warning that the system displays before the strong encryption feature gets disabled by the new permanent license. Feature licenses cannot be transferred between devices except in the case of a hardware failure.